Licensed techs, honest pricing, and same-day service across McLennan County
Boiler Replacement waco TX Done Right the First Time
When your boiler quits, you need boiler replacement waco TX homeowners can count on. We install Carrier, Trane, and Rheem systems built for Central Texas weather, and we handle everything from permits to final testing. Whether it is a cracked heat exchanger or a unit that is simply worn out, our team gets your heat and hot water back fast.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Boiler Replacement Includes
Every boiler replacement waco TX job we do includes the equipment, labor, permit, and testing. We list what is covered so you can compare quotes apples to apples. If your job needs something extra, like new gas piping or a chimney liner, we tell you upfront and price it separately.
New Boiler and Controls
We supply a new boiler sized for your home, plus a new thermostat and safety controls. Brands include Carrier, Trane, Lennox, Rheem, and Goodman. You pick the efficiency level.
Removal and Disposal
We drain and disconnect the old unit, haul it out, and dispose of it properly. No old boiler left in your garage or on the curb.
Permit and Inspection
We pull the mechanical permit with the local jurisdiction and meet the inspector on site. You get a signed-off job that meets current code.
Combustion and Safety Testing
After install, we fire the boiler and run a combustion analysis. We check for carbon monoxide, verify gas pressure, and confirm the flue is drafting correctly.
System Flush and Fill
We flush the loop, add fresh water, and bleed every zone or radiator. You get even heat in every room, not just the ones closest to the boiler.
Walkthrough and Warranty
We show you the shutoff valves, filter location, and thermostat settings. You get the manufacturer warranty paperwork plus our labor warranty in writing.
Service overview
What Boiler Replacement waco TX Really Involves
Boiler replacement waco TX is the removal of an old, failing boiler and the installation of a new unit sized and vented for your home. We start by checking your existing setup, measuring the load, and confirming gas line capacity. Then we pull the old unit, flush the system, and set the new boiler. Most jobs take one to two days, and we test every zone before we leave.
Waco homes take a beating from temperature swings. A boiler that ran fine last winter may struggle when the first cold front hits in November. If you are searching for boiler replacement near me waco, you are probably dealing with no heat, rusty water, or a unit that short-cycles. We see it every fall in older homes near downtown and in neighborhoods like Woodway and Hewitt.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
Our Boiler Replacement Process
The process flexes to the condition, but these checkpoints keep decisions clear.
Call and Schedule
You call us at (844) 681-2495 or book online. We ask about your boiler brand, age, and symptoms. Most Waco-area appointments are set within 24 hours, and we offer same day boiler replacement waco when the situation is urgent.
On-Site Assessment
A licensed tech inspects your current boiler, checks gas pressure, and measures the space. We use manifold gauges and a combustion analyzer to document what is failing. You get a written quote with equipment options before we order anything.
Equipment Selection
We walk you through Carrier, Trane, Lennox, Rheem, and Goodman options. You pick the efficiency level and features you want. We confirm the new boiler fits your venting and electrical setup so there are no surprises on install day.
Removal and Installation
We shut off gas and water, drain the old unit, and disconnect the flue. The new boiler goes in with fresh isolation valves, a new expansion tank, and updated controls. Installation usually takes four to eight hours depending on system size.
Testing and Walkthrough
We fill the system, bleed every radiator or zone, and fire the boiler. A combustion test confirms safe operation. Then we show you the thermostat settings, filter location, and shutoff valves so you know what to do if something changes.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Combustion Analyzer
Measures carbon monoxide, oxygen, and flue temperature to confirm the boiler is burning clean and safe after installation.
Manifold Gauges
Checks gas pressure at the valve and burner so the new boiler runs within the manufacturer's spec.
Vacuum Pump
Pulls a deep vacuum on refrigerant lines when we pair a boiler job with heat pump or AC work.
Refrigerant Recovery Machine
Recovers refrigerant safely when we replace a system or repair a leak on a combined heating and cooling setup.
HVAC Diagnostic Tools
Multimeters, clamp meters, and thermometers that let us trace electrical faults and verify temperature rise.
Duct Cleaning Equipment
Removes debris from ductwork when a boiler replacement uncovers dirty runs that would cut efficiency.
Use cases
When Waco Homeowners Call Us
These examples show how the service framework adapts rather than forcing every call through one repair.
Steam Boiler Swap in a Cameron Park Bungalow
A 1940s bungalow near Cameron Park had a steam boiler that banged and leaked. Two rooms had no heat, and the homeowner was using space heaters to get through January. → We replaced the steam boiler, repaired two radiator valves, and re-pitched the returns. Every room now heats, and the banging stopped. The homeowner removed the space heaters.
Emergency Replacement Before a Freeze
A rental in Bellmead lost heat on a Thursday night with a freeze forecast for Saturday. The old boiler had a failed gas valve and a cracked heat exchanger. → We sourced a Rheem boiler Friday morning and had it installed and tested by Friday afternoon. The tenant had heat before the freeze, and the landlord avoided a burst-pipe claim.
Problems we solve
Boiler Problems We Solve in Waco
Most boiler calls come down to a handful of failures. Here is what we see and how we fix it.
Boiler will not fire or stay lit
We test the igniter, flame sensor, gas valve, and control board. Most no-fire calls are a failed igniter or dirty flame sensor, which we replace on the spot. If the board is dead, we source the part and get you running.
Rusty or leaking boiler
Once a boiler shell or heat exchanger leaks, repair is not worth the money. We quote a new boiler installation waco and get it in fast. We also check the nearby water heater and piping for corrosion while we are there.
Rising gas bills with less heat
We clean the burner, check gas pressure, and test combustion. If the unit is 15 years or older, we run a cost comparison so you can see whether a high-efficiency replacement pays for itself.
Banging or knocking sounds
We flush the system, inspect the circulator, and check water chemistry. If the boiler is sound, a flush and new pump solve it. If the exchanger is cracked, we move to replacement.
Pricing process
Boiler Replacement Cost in Waco
$4,200 - $8,500 installed
Boiler Type and Size
A standard hot-water boiler costs less than a high-efficiency condensing model or a steam boiler. Larger homes need more capacity, which raises the equipment price.
Efficiency Rating
An 80 percent AFUE boiler costs less upfront than a 95 percent condensing unit. The higher-efficiency model usually pays back the difference in three to five winters.
Venting Requirements
If your old boiler used a chimney and the new one needs PVC venting, we run new pipe through a wall or roof. That adds labor and materials.
Customer reviews
What Waco Homeowners Say
★★★★★
“Our boiler died on a Friday night in January. Waco Air Conditioning & Heating had a tech out Saturday morning and a new Rheem installed by Sunday afternoon. They pulled the permit and walked me through everything. House was warm again before the next freeze.”
★★★★★
“I got three quotes for boiler replacement near me waco and these guys were the only ones who actually measured the house. The new Carrier unit cut my gas bill by about 25 percent. Clean install, no mess left behind.”
★★★★★
“I manage four rentals in Bellmead and Lacy-Lakeview. When a boiler goes out, I call these guys. They handle the tenant, pull the permit, and send me photos of the finished job. Fair prices and they do not nickel-and-dime you.”
How much does boiler replacement cost in waco TX?
Most boiler replacements in Waco run $4,200 to $8,500 installed, depending on unit size and efficiency. A standard hot-water boiler for a 1,500-square-foot home sits near the lower end. High-efficiency condensing models, steam systems, and jobs that need new venting push toward the top. We give you a written range after the on-site assessment.
How long does boiler replacement take in waco?
A typical boiler replacement takes one to two days. Most single-family homes are done in a single day if the venting and gas line already meet code. Two-story homes, steam systems, and jobs that need new piping can run into a second day. We tell you the expected timeline before we start.
When should I replace my boiler in waco Texas?
Replace your boiler when it is 15 years or older, when repairs exceed half the cost of a new unit, or when you see rust, leaks, or rising gas bills. In Waco, the best time is early fall before the first cold front. Waiting until January means you are competing with every other homeowner for emergency service.
What is the best boiler brand for waco TX homes?
Carrier, Trane, Lennox, Rheem, and Goodman all make reliable boilers for Central Texas. The best brand is the one sized correctly and installed by a certified tech. We carry multiple lines so we can match the unit to your home, your budget, and the parts availability in McLennan County.
Related services
Related Services
Air Conditioning Installation
If your boiler and AC share ductwork or a mechanical room, we can install both systems in one visit. Waco summers hit 100 degrees, so getting the cooling side right matters as much as heat.
Air Conditioning Repair
A boiler replacement often uncovers AC problems nearby, like a clogged drain pan or a failing capacitor. We fix those while we are on site so you are not booking a second appointment.
Air Conditioning Maintenance
Annual AC tune-ups keep your cooling system efficient and catch small issues before they become summer emergencies. Pair it with your boiler service and save a trip charge.Ready when you are
Get Your Boiler Replacement waco TX Quote Today
Call (844) 681-2495 and we will schedule a free on-site assessment. We give you a written price, handle the permit, and install your new boiler with a warranty on parts and labor. No heat or no hot water? We run 24/7 emergency calls.
Talk with the local team
Request Boiler Replacement
Feel free to reach out to us for any HVAC inquiries. We are available Monday through Friday, with same-day responses.